LEXUS RX 300

1998 — 2003 of release

Repair and operation of the car


Lexus RX 300
+ Lexus RX-300 cars
+ Governing bodies and methods of operation
+ Settings and routine maintenance of the car
+ Engine
+ Cooling systems of the engine, heating, ventilation and air conditioning
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   - External equipment and body elements
      Removal and installation of the top strut of a motive compartment
      Removal and installation of bumpers
      Removal and installation of a cowl, its lock and decorative front grille
      Removal, installation, dismantling and assembly of a forward door and its components
      Removal, installation, dismantling and assembly of a back door and its components
      Removal, dismantling, assembly and installation of a door of a back and its components
      Removal and installation of cleaners and fairing of a windshield
      Removal and installation of moldings
      Removal and installation of a spoiler
      Removal and installation of the top hatch
   + Equipment of salon
+ Onboard electric equipment
+ Schematic diagrams of electric connections

2598ff35

Removal, dismantling, assembly and installation of a door of a back and its components

Back door components

1 — the Washer
2 — the Side panel of finishing of a door
3 — the Lever and an edge of a screen wiper
4 — a back door Rack
5 — the Nest of a side clamp
6 — the Side clamp
7 — the lock Cylinder
8 — the Top panel of finishing of a door
9 — the Top panel of finishing flew down
10 — the Stoplight of the top level
11 — the Lower panel of finishing of a door

12 — Э / the screen wiper motor
13 — the External handle
14 — the External overlay of a door of a back
15 — the Mechanism of control of the lock
16 — Consolidation
17 — Lenses of illumination of registration plate
18 — the Handle for raising of a door.
19 — the Lock
20 — the lock Activator
21 — the Back combined lamp
22 — the lock Drummer


 PERFORMANCE ORDER

  1. Insert the screw-driver between a back door the top panel of finishing of glass and wring out the panel from clamps on its perimeter.
  2. Separate the socket and remove a stoplight of the top level from the top panel of finishing of glass.
  3. Inserting the screw-driver between a door of a back and elements of finishing of a door, wring out consistently from clamps the top panel, both side and the lower panel.
  4. Turn out a nut and remove the screen wiper lever.
  5. Turn out a nut and remove a washer э / the screen wiper motor from the outer side of a door.
  6. Separate the socket, turn out three bolts and remove э / the screen wiper motor.
  7. Separate sockets, turn out 4 bolts and remove the back combined lamps with consolidations.
  8. Disconnect the socket from the lock cylinder, turn out two bolts and remove the cylinder.
  9. Turn out two bolts, remove the mechanism of control of the lock and disconnect from it a cable.
  10. Disconnect draft from the lock, give two nuts and remove the lock activator. Separate the socket.
  11. Separate the socket, turn out 4 bolts and remove the lock.
  12. Turn out two screws and remove lenses of illumination of registration plate.
  13. Turn out two nuts and remove the external handle.
  14. Turn out a nut and wring out the screw-driver an external overlay of a door of a back from clamps.
  15. Remove the handle for raising of a door.
  16. Give fixture of loops to a door and remove a door.
  17. At installation of a door, especially new, it is necessary to adjust its situation.
  18. For adjustment of a door in the directions give bolts of fastening of loops to a door to the left/to the right and up/down, expose a door in required position and tighten bolts with effort of 8 Nanometers.
  19. For adjustment of a door in the directions give bolts of fastening of loops to a body up/down and inside/outside, expose a door in required position and tighten bolts with effort of 12 Nanometers. For a reversing of bolts at first:
    • Remove a lens of the lamp of the luggage compartment;
    • Turn out four bolts, separate the socket and remove the lamp;
    • Wring out the screw-driver back section of finishing of a roof from clamps and remove it.
  20. If necessary adjust position of the drummer of the lock, moving it (tapping with the hammer) at the released fixture outside/inside and up/down. Previously remove the lower panel of finishing of a doorway of a back. Upon termination of adjustment tighten bolts of fastening of the drummer with effort of 23 Nanometers and install the panel.
  21. In conclusion adjust the provision of a side stopper.
  22. Installation is made upside-down. Tighten fixture with the required efforts, use new clamps.
  23. In conclusion of installation adjust provisions of the lever of a screen wiper (see the Section Check of a State, adjustment and replacement of brushes of screen wipers).
  1. After installation check that the top point of hit of a stream of the washing liquid on glass was in the shaded area, and the lower point – in a screen wiper scope.