LEXUS RX 300

1998 — 2003 of release

Repair and operation of the car


Lexus RX 300
+ Lexus RX-300 cars
+ Governing bodies and methods of operation
+ Settings and routine maintenance of the car
+ Engine
+ Cooling systems of the engine, heating, ventilation and air conditioning
+ A power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Automatic transmission and interaxal differential
+ Transmission line
+ Brake system
+ Suspension bracket and steering
- Body
   + External equipment and body elements
   - Equipment of salon
      Removal and installation of the dashboard and main ware box
      Removal of a carpet of a floor and ware box of the central console
      Removal and installation of finishing of a ceiling
      Removal, dismantling, assembly and installation of front seats
      Removal, dismantling, assembly and installation of back seats
      Removal and installation of seat belts and their emergency natyazhitel
+ Onboard electric equipment
+ Schematic diagrams of electric connections

2598ff35

Equipment of salon

Removal and installation of the dashboard and main ware box

Dashboard components

1 — the Intensifying bar
2 — the Returnable spring of a pedal
3 — Assembly of a safety cushion of the forward passenger
4 — the Arm No. 2
5 — the Arm No. 1
6 — the loudspeaker Panel No. 1
7 — ECU ABS
8 — the Overlay of the dashboard
9 — ECU of a body
10 — Assembly of the multipurpose display
11 — the Panel of finishing of the central console
12 — separate Side segments the central console
13 — Assembly of the audio system
14 — the Air duct
15 — Nizhny Novgorod a segment of finishing of the central section of the dashboard
16 — the Fringing
17 — the Panel of finishing of the lock of ignition
18 — the Lower panel of the central section of the dashboard
19 — Assembly of the lever of the selector of the AT modes

20 — the Panel of finishing of the lower console
21 — the Lower insert
22 — the Understeering panel
23 — Nizhny Novgorod the holder No. 2
24 — Nizhny Novgorod the holder No. 1
25 — the Combination of devices
26 — Finishing of a forward rack of a body
27 — Finishing of a combination of devices
28 — the Lower panel No. 2
29 — a CD changer
30 — the Side segment of the dashboard (right)
31 — the Combined switch
32 — the Lower cover No. 2
33 — the Lower side panel
34 — the Side segment of the dashboard (left)
35 — Casings of a steering column
36 — the Steering wheel
37 — Finishing of a threshold of a forward door
38 — the Overlay of a steering wheel

Components of a path of system of ventilation

1 — Finishing of the deflector of an obduv of a windshield
2 — Assembly of the deflector of an obduv of a windshield
3 — the Overlay of the dashboard
4 — the Gate No. 4
5 — the Side deflector No. 2
6 — the Electrical wiring
7 — the Air duct No. 5 of the side deflector
8 — the Air duct of the side deflector No. 2
9 — the Air duct from a heater to the gate No. 4

10 — the Central air duct from a heater to the gate
11 — Assembly of the lamp in a ware box
12 — the Central arm
13 — the Air duct from a heater to the gate No. 1
14 — the Air duct of the side deflector No. 1
15 — the Sensor of the sun
16 — the Sensor of automatic control of lighting
17 — the Arm No. 1
18 — the Side deflector No. 1
19 — the Gate No. 1


On сопр. illustrations the type of fixture of the listed components is also specified: letters with A on F designated bolts and screws, by the letters G and H – nuts, but components which are not designated by letters fasten clamps.


 PERFORMANCE ORDER

  1. Consistently remove dashboard components 30, 34, 37, 26, 33, 6 and 32, having released them from clamps.
  1. Separate the safety cushion socket, trying not to damage an electrical wiring.
  1. Remove the lower panel No. 2, having turned out 2 bolts and 2 screws.
  1. At the corresponding complete set turn out 4 nuts, separate the socket and remove a CD changer.
  1. Turn out 2 bolts and 2 nuts and remove assembly of a safety cushion.

After removal lay assembly of a safety cushion face up. Do not investigate assembly of a safety cushion. At installation tighten fixture with the required efforts, replace assembly of a safety cushion with visible damages, do not allow short circuit of an electrical wiring of a safety cushion.

  1. Remove a steering wheel with a slip, and also casings of a steering column (see the Section Removal, installation, dismantling and assembly of a steering column).
  2. Consistently remove dashboard components 17, 20, 22 and 21, having released them from clamps and having turned out 2 bolts in the last two cases.
  3. Remove a steering column (see the Section Removal, installation, dismantling and assembly of a steering column).
  4. Consistently remove dashboard components 16, 12 and 18, having released them from clamps and having turned out in the latter case 6 screws.
  1. Turn out 4 bolts and remove the panel of finishing of the central console.
  1. Separate sockets, turn out 4 bolts and remove assemblies of the multipurpose display and the audio system.
  1. Turn out 2 screws and remove finishing of a combination of devices.
  1. Separate the socket, turn out 3 screws and remove a combination of devices.
  2. Turn out two bolts and remove the lower holders (23 and 24).
  3. Separate the socket, disconnect draft, give 4 nuts and remove assembly of the lever of the AT selector.
  4. Remove air ducts.
  1. Separate sockets, turn out 2 bolts and 2 nuts and remove an overlay of the dashboard.
  1. Give fixture and remove arms No. 1 and No. 2 (4 and 5).
  2. Turn out 2 nuts and remove modules of management of a body and ABS.
  3. Remove a returnable spring, turn out a bolt, 2 nuts and remove the block of the relay and safety locks under the dashboard.
  1. Turn out 4 bolts and 4 nuts and remove an intensifying bar.
  1. Consistently remove components No. No. 11, 12, 18, 5, 1, 2, 7, 14, 8, 13, 9, 19, 4, and 10.
  1. Turn out 5 screws, wring out clamps and remove an electrical wiring.
  1. Turn out 2 screws and remove an arm No. 1.
  2. Remove the sensor of the sun and the sensor of automatic control of lighting.
  3. Installation is made upside-down. Tighten fixture with the required efforts, replace the deformed clamps.