Lexus RX 300 - Lexus RX-300 cars Identification numbers of the car Acquisition of spare parts Technology of service, tool and equipment of a workplace Поддомкрачивание / posting and emergency transportation of the car Start of the engine from the auxiliary power supply Automobile chemicals, oils and lubricants Diagnostics of malfunctions + Governing bodies and methods of operation + Settings and routine maintenance of the car + Engine + Cooling systems of the engine, heating, ventilation and air conditioning + A power supply system and production of the fulfilled gases + Systems of electric equipment of the engine + Automatic transmission and interaxal differential + Transmission line + Brake system + Suspension bracket and steering + Body + Onboard electric equipment + Schematic diagrams of electric connections
|
Diagnostics of malfunctions The description of diagnostics of electronic control systems and codes of malfunctions are provided in the Head Sistemy of electric equipment of the engine. In this section the simplest scheme of clarification of the reasons of the malfunctions and refusals happening in knots and systems of the car is offered. Refusals and their possible reasons are broken into groups on a sign of the relation to certain components or systems of the car, such as the engine, the cooling system, etc., besides, in the text references to chapters and sections concerning these problems are given. Remember that the successful completion of search of causes of defect is defined by integrity of a complex of good knowledge and patient, systematic approach to a problem research. It is necessary to move always from simple to difficult, to bring each check to the logical end and to try not to pass the obvious facts - everyone can forget to fill fuel in the fuel tank or to leave included in lighting fixtures for the night. And, at last, it is always necessary to try to make a clear picture of development of malfunction and to take the corresponding steps for prevention of a recurrence. If the failure of electric equipment happened for a cause of infringement of quality of contact, check a condition of all other contacts and electric sockets of system at the same time. If the same safety lock fused several times in a row, there is no sense in its further replacement - try to find out a cause of failure. Remember that failure of a minor component can be a sign of violation of functioning of more important knot or the whole system. Engine Indispensable conditions of start of any petrol engine are serviceability of supply of air-fuel mix in cylinders and timely sparking on spark plugs. First of all it is necessary to make sure of serviceability of supply of fuel. To define whether the spark is formed, turn out spark plugs, insert them into tips and separately apply to weight. At the same time it is not necessary to hold a wire or a tip hands, - use the isolated flat-nose pliers. Ask the assistant to start the engine. If the spark is absent, try to define a cause of failure. The engine is not turned in attempts of its start
- Plugs of the battery are oxidized or fastening of tips of wires on them weakened.
- The battery is discharged or faulty. If tips of wires are not oxidized and reliably fixed on battery plugs, turn the ignition key in the provision of "ON", then include headlights and/or screenwashes, - if they do not function, - the battery is discharged.
- Transmission it is inexact it is established in situation "P".
- Gap in a chain of system of start.
- The gear wheel of a starter is jammed in a gear wreath of a driving disk.
- The traction relay of a starter is faulty.
- The starter is faulty.
- The ignition switch is faulty.
The engine is turned, but not started
- Start is incorrectly made. Act according to the Section Start of the Engine and a start of motion.
- The engine immobilizator is faulty or is not disconnected.
- The emergency switch of the fuel pump is faulty.
- The fuel tank is empty, or low-quality fuel is filled.
- The air filter is strongly polluted. Leak of vacuum in elements of air supply, malfunction in a control system of injection of fuel and ignition takes place.
- The battery is discharged (the engine is turned too slowly).
- Plugs of the battery are oxidized or fastening of tips of wires on them weakened.
- The fuel pump is faulty, or its relay is damaged, - aurally check turning on of the pump at inclusion of ignition.
- Components of system of ignition are damaged or excessively moistened.
- Spark plugs are worn-out or faulty, or the candle gap is incorrectly exposed.
- Gap in a chain of system of start.
- The ignition coil electrical wiring is torn off or disconnected, or or fastening of wires on coil plugs weakened.
- The safety lock of the control unit of the engine is damaged, it is faulty a control system of the engine, any of sensors.
- Low pressure of a compression.
The starter functions without engine provorachivaniye
- The starter gear wheel is jammed.
- Teeths of a gear wheel of a starter or wreath of a driving disk are worn-out or damaged.
Start of the cold engine is complicated See also Cold engine it is started badly, works unstably.
- Low level of a charge of the battery.
- Power supply system components, or electric equipments are faulty.
Start of the hot engine is complicated See also Heated-up engine it is badly started, works unstably.
- The air filter is littered.
- Power supply system components, or electric equipments are faulty.
- Fuel does not arrive to injectors.
- Insufficient compression in cylinders.
Gearing of a starter happens is too noisy or with difficulty
- Teeths of a gear wheel of a starter or wreath of a driving disk are worn-out or damaged.
- Are lost, or bolts of fastening of a starter are insufficiently tightened.
The engine is started, but at once becomes deaf
- The engine immobilizator is faulty.
- The electrical wiring is faulty, or fastening of wires on plugs of the coil of ignition or the generator weakened.
- Power supply system components, or electric equipments are faulty.
- Basic installations of the control unit of the engine (ECM) are broken.
- Damage to system of release and decrease in toxicity of the fulfilled gases (FG) takes place.
- Losses of depression on the throttle case, the inlet pipeline or through vacuum hoses take place.
Stability of operation of the engine on single turns is broken
- Depression losses take place. Make sure of reliability of tightening of fixture, check the fact and quality of fastening on the unions on the inlet pipeline of all vacuum hoses. Wiretap the working engine by means of a stethoscope or a piece of a fuel hose - existence of the hissing sound demonstrates leak existence. Not less effective use of soap solution for check.
- Serviceability of functioning of components of a power supply system or electric equipment is broken.
- Passability of the valve of system of the operated ventilation of a case (PCV) is broken.
- Passability of the air filter is broken.
- The fuel pump does not provide giving of enough fuel to injectors.
- Leaks through laying of a head of cylinders take place, - measure a compression in engine cylinders (see the Head Dvigatel).
- Working ledges of cams of the camshaft are worn-out.
Admissions in operation of cylinders on single turns take place
- Spark plugs are worn-out or polluted or the candle gap is incorrectly exposed.
- Malfunction of components of a power supply system or electric equipment takes place.
- It is faulty In/in an electrical wiring.
- Low-quality fuel is filled, or passability of the fuel filter is broken.
- Losses of depression in the inlet pipeline or through hose connections take place.
- Low or different compression in cylinders.
- Work of a control system of the engine is broken.
Admissions in operation of cylinders of the engine at the movement of the car on transfer take place
- The fuel filter is hammered or pollution of a power supply system takes place.
- Spark plugs are faulty or polluted or the candle gap is incorrectly exposed.
- Malfunction of components of a power supply system or electric equipment takes place.
- It is faulty In/in an electrical wiring.
- Components of system of decrease in toxicity of the fulfilled gases are faulty.
- Low or different compression in cylinders.
- The system of ignition is faulty.
- Losses of depression on the throttle case, the inlet pipeline or through vacuum hoses take place.
The engine spontaneously becomes deaf
- Adjustment of turns of idling is broken.
- Passability of the fuel filter is broken, or moisture or dirt got to a power supply system.
- The refusal of components / information sensors of a power supply system takes place.
- Components of systems of decrease in toxicity of the fulfilled gases are faulty.
- Spark plugs are faulty or polluted or the candle gap is incorrectly exposed.
- Losses of depression on the case of a throttle or through vacuum hoses take place.
The engine does not develop full capacity
- Malfunction of components of a power supply system or electric equipment takes place.
- The air cleaner is littered.
- Spark plugs are faulty or the candle gap is incorrectly exposed.
- The ignition coil is faulty.
- The ATF level fell (see the Head Nastroyki and routine maintenance of the car).
- Transmission revolves.
- The fuel filter is hammered and/or dirt/moisture got to a power supply system.
- Low-quality fuel is filled.
- Low or different compression in cylinders.
There are cottons in system of an admission or shots in system of release
- Serviceability of functioning of components of a power supply system or electric equipment is broken.
- Defect in a secondary contour of system of ignition takes place (destruction of insulators of spark plugs or damage In/in wires).
- The system of injection of fuel needs adjustment, or its components are excessively worn-out.
- Losses of depression on the throttle case, the inlet pipeline or through vacuum hoses take place.
- Gets jammed valves.
- The connection order In/in wires is broken.
At the movement with acceleration or uphill there are detonation sounds
- Low-quality fuel is filled.
- Power supply system components, or electric equipments are faulty.
- Spark plugs not of that type are established.
- The basic ECM installations are broken.
- The detonation sensor is faulty.
- Depression losses take place.
The engine continues to work after turning of a key in the provision of "OFF"
- Idling turns are excessively high.
- Malfunction of electric equipment or components of a control system of the engine takes place.
- The valve of a purge of an adsorber of system of catching of vapors of fuel (EVAP) is faulty.
- High working temperature of the engine (the OZh level fell, the thermostat is faulty, the radiator is hammered or the water pump is faulty).
- Tightness of injectors is broken.
Engine electric equipment Decrease in capacity or insufficient charge of the battery
- The generator drive belt is worn-out or damaged, or adjustment of its tension is broken.
- Level of electrolyte is insufficient or the battery is strongly discharged.
- Plugs of the battery are oxidized or fastening of tips of wires on them weakened.
- The generator does not provide the required charging current.
- Gap in a chain of an electrical wiring of a charging contour.
- Short circuit on "mass" of an electrical wiring creates continuous leakage of the current developed by the battery.
- Internal defect of the battery takes place.
The control lamp of charging does not die away at increase in turns
- The tension of a driving belt is weakened.
- The regulator of tension and/or the generator is damaged. Disconnect a wire (D+) from a reverse side of the generator and include ignition. Further check a condition of the regulator of tension of the generator.
- Generator brushes are worn-out.
- The wire between the generator and the regulator of tension is damaged.
- The combination of devices is faulty.
The control lamp of charging does not light up when turning a key in the provision of "ON"
- The control lamp failed.
- The generator is faulty.
- Defect of the printed circuit board, conducting in the block of a combination of devices or the boss of a lamp takes place.
The control lamp of charging does not die away when turning a key in the provision of "OFF"
- Diodes are punched.
Starter
|
Contact plugs of an electrical wiring have to be reliably fixed and are not oxidized! |
- If the starter is not turned, at first it is necessary to make sure that at the plug No. 50 of the traction relay there is tension (at least 10 V). At negative results check a condition of an electrical wiring of a contour of current of a starter.
- For check of serviceability of operation of a starter at a full tension of the battery perform the following operations:
- Not including transfers, turn a key in the provision of "ON";
- Peremknite starter plugs 30 and 50 wire with a section not less than 4 mm2.
- If the starter works faultlessly, the cause of defect should be looked for in wires to a starter. If the starter does not earn, it should be checked in the removed state.
The starter does not rotate when turning a key in situation "START"
- The battery is discharged.
- Peremknite starter plugs 30 and 50: if the starter rotates, check the wire 50 brought to the ignition lock for break, also estimate a starter switch condition.
- The weight wire is torn off, or quality of its terminal connection is broken.
- Weakening of current owing to violation of quality or oxidation of contact connections.
- There is no tension on the plug of the 50th traction relay as a result of break of an electrical wiring, or damage of the switch of a starter.
The starter rotates slowly and does not turn a bent shaft
- The battery is discharged.
- Summer oil is filled in.
- Passing of current owing to low-quality contacts is complicated.
- Coal brushes do not adjoin to a collector, jam in guides, are worn-out, broken, greasy or polluted.
- Insufficient distance between brushes and a collector.
- The collector in grooves or burned and was made oily.
- There is no tension on the plug 50 (at least 8 V).
- The bearing is broken.
- The traction relay is faulty.
The starter "grabs", but provides only a ryvkoobrazny provorachivaniye of the engine
- The gear wheel drive is faulty.
- The gear wheel is polluted.
- The gear wreath of a driving disk is damaged.
The gear wheel of a starter does not leave gearing with a gear wreath of a flywheel / a driving disk
- Gear wheel drive components are polluted or damaged.
- The traction relay is faulty.
- The returnable spring weakened or became torn.
The starter continues to work after an ignition key otpuskaniye
- The traction relay is jammed, - immediately switch off ignition and replace the traction relay.
- The ignition lock is not switched-off, - switch-off the battery, replace the lock.
Power supply system Fuel consumption is excessive
- The air filter is polluted or hammered.
- Pressure of a rating of tires is not enough or tires not of that size are installed.
- The engine has mechanical damages. Check a compression, in case of need make the corresponding recovery repair.
- Turns of idling and the maximum turns of a bent shaft are excessively high.
- Malfunctions of components of a power supply system, electric equipment or electronic control.
- Leaks in system of an admission of air.
- Damages to system of release and decrease in toxicity of OG.
Leak of fuel and/or a smell of gasoline takes place
- Leaks in lines of supply of fuel or ventilating lines take place.
- The fuel tank is overflowed. You make gas station only before automatic shutdown of the gun.
- Take place leak/evaporation from lines of power supply systems and decrease in toxicity of OG.
The engine is not started
- At inclusion of a starter the fuel pump does not work (noise from work is not heard). Slightly knock on a pump housing to release the jammed detail. Check serviceability of giving of tension for the pump (check serviceability of a safety lock and reliability of fastening of contact plugs of the corresponding electrical wiring).
- The relay of the fuel pump is faulty.
- Valves of injectors stuck. Check injectors, if necessary replace. Check giving of tension for injectors.
- There is no signal from the sensor of ignition or the ECT sensor. Check a condition of its electrical wiring, carry out a survey of memory of the OBD II system.
- Fuel pipelines are damaged, littered or untight, there are defects of hoses.
- The fuel filter is littered.
- To the inlet highway as a result of violation of tightness excess air podsasyvatsya.
- Vacuum pipelines are damaged, or violation of tightness of their landing takes place.
- The fuel pressure regulator is damaged, - check residual pressure.
- The sensor of provision of a butterfly valve (TPS) is damaged.
- There is no ECM food.
- Ventilation of the fuel tank is hammered, the filter in a tank is littered.
The cold engine is started badly, works unstably
- The maintenance of CO does not conform to standard requirements, - perform the corresponding measurement, check idling turns.
- The ECT sensor is faulty.
- Pressure of fuel does not correspond to the required value.
- To the inlet highway as a result of violation of tightness excess air podsasyvatsya.
The heated-up engine is badly started, works unstably
- The system of an admission of air is untight. Check inlet system. For this purpose leave the engine to idle and moisten places of consolidations and connection on an inlet path with gasoline. If speed for a short time increases, eliminate untight places.
- The backpressure valve of the fuel pump is damaged.
- Leaks in fuel system.
- Elevated pressure of fuel in a power supply system.
- Malfunction of the EVAP system.
- The returnable fuel-supply line to a tank is hammered or crumpled.
- Valves of injectors stuck. Check injectors, if necessary replace. Check giving of tension for injectors.
- There is no signal from the sensor of ignition of Hall or the sensor of temperature of cooling liquid. Check a condition of the corresponding electrical wiring, carry out a survey of the OBD II system.
- To the inlet highway as a result of violation of tightness excess air podsasyvatsya.
- Pressure regulator is damaged, - check residual pressure.
- The TPS sensor is damaged.
- There is no ECM food.
The engine works with interruptions
- Connections of an electrical wiring of the fuel pump are broken from time to time. Check sockets of an electrical wiring and safety locks of the fuel pump, MAF sensor and relay of the fuel pump.
- Poor quality of fuel, formation of steam traffic jams.
- Weak service of fuel.
- The fuel filter is faulty.
- The fuel pump is faulty.
- Injectors are faulty.
- It is faulty a lambda probe, violations in a chain of quality management of mix or there is no heating a lambda probe.
- TPS is faulty.
- The final collector or reception pipe of system of production of the fulfilled gases is damaged (there are leakages of OG).
- Malfunction of the EVAP system.
- Valves of injectors stuck. Check injectors, if necessary replace. Check giving of tension for injectors.
- There is no signal from the sensor of ignition of Hall or the ECT sensor. Check an electrical wiring, carry out a survey of memory of ECM on existence of codes of malfunctions.
- To the inlet highway as a result of violation of tightness excess air podsasyvatsya.
- Vacuum pipelines are damaged or untight
- Pressure regulator is damaged, - check residual pressure.
- There is no ECM food.
The engine works with interruptions on the transitional modes and in the idling mode
- The system of an admission of air is untight. Check connections of inlet system. Start the engine and moisten with gasoline of connection of components of the soaking-up path. If engine turns quickly increase, remove a tightness cause of infringement.
- Idling adjustment is incorrect. Check TPS and a lambda adjustment.
The hot engine is not started
- Incorrect adjustment of contents WITH. Check contents WITH and idling.
- Too high pressure in fuel system, - check fuel pressure, if necessary replace pressure regulator.
- The returnable pipeline between the regulator of pressure and the fuel tank is littered or bent. Clean or replace the pipeline.
- The engine temperature sensor is faulty.
- Tightness of a power supply system is broken.
- Tightness of an inlet air path is broken.
Lubrication system The control lamp does not burn when turning a key in the provision of "ON"
- The oil pressure sensor is faulty. Include ignition, disconnect a wire from the sensor and close it on "weight", - if the lamp lights up, replace the sensor.
- On the sensor tension, contacts of a korrozirovana does not move, - check a condition of the corresponding electrical wiring.
- The control lamp is faulty.
- The combination of devices is faulty.
The control lamp does not die away after start of the engine
- Oil is overheated. If the control lamp dies away after gas supply, it is required to do nothing.
The control lamp does not die away after gas supply, or lights up during the movement
- Oil level fell.
- Short circuit of an electrical wiring of the sensor of level of oil takes place.
- The sensor is faulty.
Too low pressure of oil on all turns
- Oil level fell.
- The mesh filter of a maslozabornik in the case pallet is littered.
- The oil pump is worn-out.
- Bearings of a bent shaft are damaged.
Too low pressure of oil on small turns
- The reducing valve stuck abroach because of pollution.
Too high pressure of oil with a frequency of rotation of the engine over 2000 rpm
- The reducing valve does not open because of pollution.
Cooling system Overheat
- Level of cooling liquid fell.
- The belt of the drive of the water pump is worn-out or damaged or adjustment of its tension is broken.
- Internal canals of a radiator are filled or it is polluted the front grille (is blocked).
- The thermostat is faulty.
- Blades of a krylchatka of the fan are broken or burst.
- The fan sensor switch is faulty.
- The index of temperature of cooling liquid is faulty.
- The water pump is faulty.
- Does not hold pressure a radiator cover, - make check of a cover under pressure.
Overcooling
- The thermostat is faulty.
- Indications of the measuring instrument of temperature are inexact.
External leak of cooling liquid
- Hoses are damaged or destroyed as a result of material aging or their fastening on unions weakened.
- Epiploons of the water pump are spoiled, - cooling liquid exudes through a control opening in a pump housing.
- Leaks from internal channels of a radiator or the tank take place.
- Leaks through a drain stopper of the engine or release traffic jams of water galleries take place.
Internal leak of cooling liquid
|
Internal leak of cooling liquid usually comes to light by check of a condition of motive oil. Examine an edge of the measuring probe and internal surfaces of a cover (covers) of cylinders on existence of traces of water and foaming of oil. |
- Leaks through laying of a head of cylinders take place, - make check of the cooling system pressure.
- There are cracks on walls of cylinders or in casting of a head.
There are losses of cooling liquid
- In system the excessive amount of the cooling liquid (CL) is filled.
- OZh boils away as a result of an engine overheat.
- Internal or external leakages of OZh take place.
- The radiator cover is faulty, - check a cover pressure.
Circulation of cooling liquid is broken
- The water pump does not function properly. It is the simplest to make sure of functioning of the pump having pressed the top hose of a radiator at the engine working at single turns. If at an otpuskaniye of a hose the liquid push in it is felt, the pump functions regularly.
- Passability of the cooling system is broken - wash out it and fill with fresh liquid. If necessary remove a radiator and carry out its obratnopotochny washing.
- The driving belt of the water pump is worn-out or damaged or adjustment of its tension is broken.
- The thermostat is jammed.
Heater The fan of a heater does not work
- The safety lock э / the fan motor is faulty.
- The fan switch is faulty, - check whether tension to preresistors moves, remove and check the fan switch.
- The fan motor is faulty э/. Check whether tension at the included ignition and the closed fan switch moves on it, - if tension moves, replace the motor.
The fan of a heater does not work at one of steps
- The preresistor is faulty.
The heater is not switched off by the regulator
- The switch is faulty.
- Cables of the adjusting mixing gate are damaged or badly mobile.
Too low power of heating
- Level of cooling liquid is insufficient.
- Handles of management of a heater have the heavy course - check assembly of management, if necessary replace the corresponding driving cable.
Noise in the field of the heater fan
- Dirt, leaves got, - remove the fan and clean it, clear the air channel.
- Balancing of a krylchatka is broken, the bearing is damaged.
Automatic Transmission (AT) In view of complexity of a design of AT it is desirable to make diagnostics of its malfunctions and repairs of components in a workshop of car service. The common problems connected with functioning of the mechanism of switching
- It is possible to carry the following to number of the refusals connected with violation of adjustment of draft of switching:
- Start of the engine is possible at provisions of transmission, excellent from "Р" and "N";
- Indications of the indicator of provision of transmission differ from really chosen transfer;
- The car moves at the transmission established in situation "P" or "N";
- Transfers switch hardly or randomly.
- Make adjustment of draft of gear shifting.
Transmission revolves, switches hardly, publishes extraneous noises or does not provide the movement of the car at installation on one of transfers
- There is a set of the possible reasons of the problems listed in heading, however under competence of the amateur mechanic only one of them - the wrong level of transmission liquid (ATF) gets.
- Before driving away the car in a workshop of car service check the level and a condition of ATF. Modify the ATF level or replace it.
Leak of transmission liquid (ATF) takes place
- ATF has dark red color. Traces of its leaks should not be confused to traces of motive oil which can be demolished on a transmission case by the running air stream.
- For identification and localization of a source of leak first of all remove all traces of dirt and lubricant from the transmission boat. Use suitable degreaser and/or make steam cleaning. Then make on the car a short trip at a small speed (that traces of leak did not communicate the running stream far from its source). Stop, the car and by visual survey establish to a poddomkratta a leak source. Most often act as those:
- The transmission case pallet, - tighten fixing bolts and/or replace laying of the pallet;
- Tube of ATF gas station, - replace rubber consolidation in the place of an entrance of a tube to a transmission case;
- The ATF lines, - tighten nipple connections or replace lines;
- The ventilating tube, - transmission is crowded and/or water got to it.
ATF has brown color or smells of ashes
- The ATF level is insufficient.
The kickdown mode does not join by full pressing a pedal (the low gear does not join)
- The ATF level fell.
- The control system of the engine is faulty.
- The sensor switch or its electrical wiring is faulty.
- Adjustment of a driving cable of the selector is broken.
The engine is not started at any position of the selector or also "R" is started in provisions, excellent from "Р"
- Adjustment of the sensor switch of permission of start is broken.
- Serviceability of functioning of a control system of the engine is broken.
- Adjustment of a cable of the selector is broken.
Transmission revolves, breakthroughs or noise at gear shifting. The car does not move at inclusion of the D or R modes
- The ATF level fell.
- The sensor or its electrical wiring is faulty.
- Serviceability of functioning of a control system of the engine is broken.
Bridges Extraneous noises
- Usual road noise, - adjustment do not give in.
- Noise of tires, - check a condition of protectors and pressure of a rating of tires.
- Bearings of wheels are worn-out or damaged, or the effort of their tightening weakened.
Vibrations
- Check a condition of bearings of wheels, serially poddomkrachivy the corresponding corner of the car and rotating a wheel manually. Listen at the same time to the sounds proceeding from the bearing. Remove bearings and check their state.
Oil leak
- Epiploons of differentials are damaged.
Brake system
|
Before coming to final conclusion about existence of problems with the brake system make sure that tires are in satisfactory condition and are beefy with the required pressure, adjustment of angles of installation of forward wheels is not broken and the car is not loaded unevenly. |
The increased brake pedal course
- The working contour of a brake path is damaged, - check system for leaks.
The pedal of a brake springs and fails
- Air got to the brake highway, - pump over system.
- Liquid level fell in the GTTs tank, - make the corresponding adjustment, pump over system.
- Formation of vials of steam. It is shown, mainly, at big load of brakes. Replace brake fluid, remove air from system.
Decrease in effect of braking, pedal fails
- Tightness of a hydraulic path is broken.
- Cuffs in the main thing or working brake cylinders are damaged.
Bad braking, despite big effort of pressing of a pedal
- Brake slips are greasy.
- The improper or hardened blocks are established.
- The amplifier of brakes is faulty.
- Brake shoes are worn-out.
When braking the car takes away aside
- Pressure of a rating of tires does not correspond to demanded.
- Protectors are unevenly worn-out.
- Brake slips are greasy.
- On one axis different brake shoes are established.
- Brake shoes are excessively worn-out.
- Mines of supports are polluted.
- Supports are damaged by corrosion, - make replacement.
- Blocks are unevenly worn-out.
Spontaneous braking
- The compensation opening in the main brake cylinder (MBC) is littered.
- The gap between a driving rod and the GTTs piston is insufficient.
Brakes heat up during the movement
- The compensation opening in the main brake cylinder is littered.
- The gap between a driving rod and the GTTs piston is insufficient.
Brakes shiver
- Blocks of inadequate type are established.
- Brake disk in places корродирован.
- The beating of a brake disk is excessively big.
Brake shoes do not depart from a brake disk, the wheel is hardly turned manually
- Corrosion in cylinders of brake supports. Repair or replace a support.
Uneven wear of blocks
- Blocks of inappropriate type are established. Replace blocks.
- Supports are damaged by corrosion, - make replacement.
- The piston stroke is complicated.
- Tightness of a path of the brake system is broken.
Wedge-shaped wear of brake shoes
- The brake disk rotates not parallel to a support.
- Supports are damaged by corrosion, - make replacement.
- Serviceability of functioning of the piston is broken.
Scratch of brakes
- Often the reason in atmospheric influence (humidity of air). If the scratch appears after the long parking at the increased humidity and then vanishes, it is not necessary to do anything.
- Blocks of inappropriate type are established.
- The brake disk rotates not parallel to a support.
- The mine of a support is polluted.
- Springs of fastening of blocks are bent.
- Press springs are stretched.
Brake pedal pulsation
- Sign of normal operation of ABS.
- The beating of a brake disk is excessively big.
- The brake disk rotates not parallel to a support.
The control lamp of ABS lights up during the movement
- Supply voltage (lower than 10 V) is not enough. Check tension. Check whether the control lamp of the generator after start of the engine dies away. If everything is all right, check a generator drive belt.
- Malfunction of ABS takes place, - check a state and reliability of fixing of terminal connection of mass of the returnable pump (in the hydromodulator).
Suspension bracket and steering The car takes away at the movement in one of the parties
- Tires are pumped unevenly up.
- Defect of tires takes place.
- Components of a suspension bracket or steering are excessively worn-out.
- Carrying out adjustment of angles of installation of forward wheels is required.
- Forward brake mechanisms are taken.
Breakthroughs, pulling or vibrations take place
- Balancing of wheels is broken or ovality of disks appeared.
- Bearings of wheels are worn-out, the effort of their tightening weakened or adjustment is broken.
- Racks shock-absorbers or other components of a suspension bracket are worn-out or damaged.
Excessive rocking of the car /" a zaryvaniye" his nose on turns takes place or when braking
- Suspension bracket racks are faulty.
- Suspension bracket components are damaged.
Too hardly the steering wheel rotates
- Excessively liquid level fell in the tank of the hydraulic booster of steering (GUR).
- Tires are pumped incorrectly up.
- Hinges of the steering drive are insufficiently greased.
- Adjustment of angles of installation of forward wheels is broken.
- GUR does not develop the required power.
The excessive side play of steering takes place
- The effort of tightening of bearings of forward wheels weakened.
- Components of a suspension bracket or steering are excessively worn-out.
GUR does not develop due effort
- It is worn-out, or the driving belt of the pump GUR is damaged, or adjustment of its tension is broken.
- Excessively GUR liquid level fell.
- Passability of hoses or lines of hydraulic system is broken.
- Air got to GUR, - pump over system.
Excessive wear of protectors takes place (not in one some area)
- Tires are pumped incorrectly up.
- Balancing of wheels is broken.
- Disks of wheels are damaged.
- Components of a suspension bracket or steering are excessively worn-out.
Excessive wear of protectors on an outer edge takes place
- Tires are pumped incorrectly up.
- Turns are too sharply made.
- Adjustment of angles of installation of forward wheels (excessive convergence) is broken.
- The suspension bracket lever is bent or twisted.
Excessive wear of protectors on an inner edge takes place
- Tires are pumped incorrectly up.
- Adjustment of angles of installation of forward wheels is broken (divergence).
- Components of steering are damaged or their fastening weakened.
Local wear of a protector takes place
- Balancing of wheels is broken.
- Disks are damaged or bent.
- Defect of tires takes place.
Defects of brushes of a screen wiper Slipping
- Rubber working elements are polluted.
- Edges of brushes are shabby, rubber working elements are worn-out or broken off.
In the field of cleaning the water remains gather in drops at once
- The windshield is polluted by varnish polish or oil.
The brush clears unilaterally - in one party well, in another is not present
- The rubber working element has unilateral wear.
- The lever of a screen wiper is twisted, the brush not precisely adjoins to glass.
Crude surfaces
- Reliability of fixing of a working element in a brush frame is broken.
- The brush adjoins to glass unevenly.
- Pressing force the lever is too small, - slightly grease hinges of levers of a screen wiper and spring or install the new lever.
Defects of tires Strong wear of the tire on both parties of a working surface
- Too low pressure in tires.
Strong wear of the tire in the middle of a working surface on all circle of a protector
- Too high pressure in tires.
Uneven wear of a protector
- Static and dynamic disbalance of a wheel, perhaps, owing to an excessive side beating of a disk, too big side play in the bearing hinges.
Uneven wear in the middle of a protector
- Static disbalance of a wheel, perhaps, owing to an excessive vertical beating.
Strong wear of certain sites in the middle of a working surface of a protector
- Result of sharp braking.
Sawtooth wear of a protector, it is frequent together with a rupture of a fabric basis of the tire invisible outside
- Car overload. Check a condition of internal walls of tires.
Rubber uvulas on side edges of a protector (scaly wear)
- Adjustment of angles of installation of wheels is broken.
- Tires are worn-out.
- Shock-absorbers / the torsion springs / rack-mount assemblies are faulty.
Formation of agnails on one party of a protector of a forward wheel
- Adjustment of a convergence of wheels is broken.
- Tires are worn-out.
- Frequent movement on uneven surfaces. The Bystry movement on turns.
Ruptures of a cord. At first are visible only from within
- Moving through sharp stones, blows of tires, etc. at a high speed.
Unilateral wear of a working surface of a protector
- Check adjustment of disorder.
- Malfunction of ABS takes place, - check a state and reliability of fixing of terminal connection of mass of the returnable pump (in the hydromodulator).
|
|